Tumblelog by Soup.io
Newer posts are loading.
You are at the newest post.
Click here to check if anything new just came in.

December 21 2014

8079 293f 500
When attaching the extruder assembly to the X-carriage make sure that the winged nut is parallel to the edge when tightened. If not, unscrew it and retry with a different starting position.
6585 6708 500
Damaged slot for attaching the fan assembly to the X-axis carriage.
6329 7c47 500
When attaching the fan assembly to the X-axis carriage just tighten the screws lightly or this will happen.
Reposted bymetalab metalab
6166 3cd9 500
When attaching the fan assembly make sure that the toothed belt runs freely.

October 02 2014

Play fullscreen
Printing the Stanford Bunny on our Mendel90 Dibond
Reposted bymetalab metalab
4938 6f9e
Reposted bymetalabweltensturmstrohminibblerSpinNE555SakerosIntelatheaninnghizidha
2756 800c 500
Mind the max load!
2685 7351 500
Our 3D-printing setup: Mendel90 Dibond, Linux-on-a-Stick Printrun, touchscreen + keyboard and several sorts of filament.
Reposted bymetalab metalab
2446 63ee 500
"Stanford Bunny" Voronoi style in progress. (No support material, ca. 3 hours at 0.2 mm layer)
2398 13ef 500
"Stanford Bunny" Voronoi style in progress. (No support material, ca. 3 hours at 0.2 mm layer)
Reposted bynicklesssofias
2304 ac4a 500
"Stanford Bunny" Voronoi style in progress. (No support material, ca. 3 hours at 0.2 mm layer)
2225 6d28 500
"Stanford Bunny" Voronoi style in progress. (No support material, ca. 3 hours at 0.2 mm layer)
Reposted bysofias sofias
2188 3558 500
"Stanford Bunny" Voronoi style in progress. (No support material, ca. 3 hours at 0.2 mm layer)
Reposted bymetalabsydnorWallaruskrybusnicklessshallow
1234 4740 500
Two Klein Bottles printed on our Mendel 90 Dibond at 0.2 mm layer. Printing time roughly 4 1/2 hours for the orange one
Reposted bymetalab metalab
1072 e0cf 500
New spool holder for smaller filament spools. Quick hack but efficient.

September 25 2014

0208 68e1 500
finally an actually working fan-duct for me :)
Reposted fromunique-entity unique-entity

August 07 2014

1669 0a1c

You can use a heat gun to speed up the setting of the Thermocoll that was used to glue in the new thermistor on the Mendel90 hot end

August 06 2014

Early RepRap research at RFA
I had some major Metalab déjà vu at the Raumfahrtagentur. Compare their first RepStrap setup to ours :)

www.flickr.com/photos/wizard23/2996881772/
www.flickr.com/photos/wizard23/2740503782/
Reposted fromwizard23 wizard23
Early RepRap research at RFA
I had some major Metalab déjà vus at the Raumfahrtagentur. Compare their first RepStrap setup to ours :)

www.flickr.com/photos/wizard23/2996881772/
www.flickr.com/photos/wizard23/2740503782/
Reposted fromwizard23 wizard23
Early RepRap research at RFA
I had some major Metalab déjà vus at the Raumfahrtagentur. Compare their first RepStrap setup to ours :)

www.flickr.com/photos/wizard23/2996881772/
www.flickr.com/photos/wizard23/2740503782/
Reposted fromwizard23 wizard23
Older posts are this way If this message doesn't go away, click anywhere on the page to continue loading posts.
Could not load more posts
Maybe Soup is currently being updated? I'll try again automatically in a few seconds...
Just a second, loading more posts...
You've reached the end.

Don't be the product, buy the product!

Schweinderl